In my previous posts, I shared the unboxing and setup of the Cricket Quartet. Now I'm finally weaving on it, and I have a few thoughts to share!
This summer, Schacht Spindle released the Cricket Quartet, an attachment that converts their Cricket rigid heddle loom into a 4-shaft table loom. The claim is that the Quartet allows you to switch back and forth at will between a rigid heddle loom and a 4-shaft loom. At $450, this is pretty expensive, considering you also need to have the Cricket, which is currently running around $240. So all in, this would cost $700, which is a lot for a table loom. (For comparison, a used 4-shaft table loom in working condition should be around $400).
However, I already had a 15" Cricket rigid heddle loom that I used to use for teaching and demonstrations. I enjoy using it, but I knew I would use a 4-shaft table loom more. We recently moved, and my weaving space is much smaller than it used to be, so space is at a premium. Gone are my days of acquiring looms just for fun! After looking at used table looms on Craigslist, Facebook Marketplace, and Ravelry, I realized that I had already had some experience with a lot of the looms out there, and found them to be too big, too loud, or too flimsy. So I decided to give the Cricket Quartet a try. As always, Schacht does a really nice job of packaging with minimal waste, while still protecting everything inside. Soon I will be putting the loom together and using it - I'll be sure to report back! One of the things I love about the Spinner's Multitool is its versatility. Just because the name implies that it's for spinners, doesn't mean you can't use it to make your weaving weaving easier!
In weaving, the sett is how close together (or how far apart) the warp ends are. The sett is often expressed as a number, followed by the term "EPI," which stands for "ends per inch." Deciding on a sett is a skill that takes practice and plenty of sampling, but I like to use our Spinner's Multitool to get a ballpark idea of which sett to choose. First, lay the warp yarn across the multitool until you find the closest match. This is your WPI, or wraps per inch measurement. In the first image, my measurement is 22. For a balanced plain weave fabric, divide your measurement in half to get your sett. This gets us 11. While it's possible to warp most looms to 11 ends per inch using a reed substitution chart, you could also choose to round up to 12 ends per inch (for a firmer fabric) or down to 10 ends per inch (for a softer, drapier fabric). If you're using a rigid heddle loom, you'll want to choose the number that is closest to the reed you have. For a twill fabric, you usually want the sett to be a little denser. A good rule of thumb is that the sett would be 2/3 of the wraps per inch. With the same 22 WPI measurement from above, that gets us 14.5 ends per inch - but let's round up to 15 for the sake of simplicity! For a warp-faced fabric, you want the warp to be very closely spaced so that the weft doesn't show. A good rule of thumb is that the sett will between 75% and 100% of the wraps per inch measurement you take. In this example, that would between 16.5-22 ends per inch. Remember: this is just a jumping-off point to get you started! It's always important to sample to make sure you're getting the cloth you want, especially when you're using your handspun yarns. Here is the fourth episode of the Fiber Sprite Podcast! On this show, I'll talk about projects I've been working on and my visit to the Taos Wool Festival.
Knitting:
Designing:
Spinning:
Weaving:
Books: Here is the fourth episode of the Fiber Sprite Podcast! On this show, I'll talk about projects I've been working on and my visit to the Taos Wool Festival.
Knitting:
Spinning: Weaving: Books:
Taos Wool Festival:
|
Archives
January 2024
Categories
All
This website uses marketing and tracking technologies. Opting out of this will opt you out of all cookies, except for those needed to run the website. Note that some products may not work as well without tracking cookies. Opt Out of Cookies |